There are two common elevator door pocket styles. One is the vertical edge and the horizontal edge with an angle of 90 degrees, so it looks like the line is very straight and the scene splicing is very convenient, which is also a common style; The other is a 45 degree angle, so the door frame forms a whole without inflection point, so the whole door pocket looks like a whole. The two styles have their own advantages, convenient 90 degree splicing and low cost. 45 degrees looks good, but it is difficult. The coincidence degree is not high. It requires free cutting, and the cost is higher than 90 degrees. It is usually recommended to customers that 90 degree splicing is more economical.

电梯厅不锈钢电梯门套工艺节点优化，如何优化结构，避免材料浪费。一般预防措施如下：

Elevator hall stainless steel elevator door pocket process node optimization, how to optimize the structure and avoid material waste. General precautions are as follows:

1、材料厚度为1.5（实际厚度应不小于1.38）

1. The recommended thickness of the material is 1.5 (the actual thickness shall not be less than 1.38)

2、门头板的宽度小于内板的宽度，这样门才会美观。

2. The width of the door head plate is less than that of the inner plate, so that the door will be beautiful.

3、注意生产基地必需小于5mm的门装订尺寸，以保证有足够的安装和涂胶空间。

3. Note that the door binding size of the production base must be less than 5mm to ensure sufficient installation and gluing space.

4、一般不建议用胶水封住门头板与外墙覆层交界处的内角。美观大方，可以检查门套的安装质量。

4. It is generally not recommended to seal the inner corner of the junction between the door headboard and the outer wall cladding with glue. Beautiful and generous, you can check the installation quality of the door pocket.

不锈钢门套与石材碰撞，如何避免石材封闭边缘的“闪缝”缺陷？

How to avoid the "flash joint" defect of the closed edge of the stone when the stainless steel door pocket collides with the stone?

1、常规封口的缺点：石材不能保证下一条直线，所以这种封口可能会出现不锈钢插入或石材闪缝过大等情况。石材边缘在安装过程中可能会损坏。

1. Disadvantages of conventional sealing: the stone can not guarantee the next straight line, so this kind of sealing may have stainless steel insertion or too large stone flash joint. Stone edges may be damaged during installation.

2、加深封口：不锈钢封口石可以防止石材封边的缺陷，使其干净美观。

2. Deepen sealing: stainless steel sealing stone can prevent the defects of stone edge sealing and make it clean and beautiful.

门套一体成型，错位、弹跳等质量问题是非标底座造成的。建议将挡板与盖板分开，避免因底座问题造成的安装缺陷。

The door pocket is integrally formed, and the quality problems such as dislocation and bounce are caused by non-standard base. It is recommended to separate the baffle plate from the cover plate to avoid installation defects caused by base problems.

各位顾客，以上关于工地电梯门套http://www.sddtmt.com知识分享，希望能帮助新手，在使用中有任何疑问，请随时联系相关人员，我们将为您提供周到的技术支持服务。

Dear customers, the above information about the elevator door pocket on the construction site http://www.sddtmt.com Knowledge sharing, hope to help novices. If you have any questions in use, please feel free to contact relevant personnel, and we will provide you with thoughtful technical support services.