Door pocket is an architectural decoration term, which refers to the two door frames inside and outside the door. It is also directly called door frame. Its main function is to fix the door leaf, protect the wall corner and decoration. It is often used in the decoration process to protect the door from scratch, corrosion, damage and dirt.

如为前一种方法——现场制作的不锈钢门套由现场装修工人用钉子直接固定在门洞墙上；如果安装了整套门产品的不锈钢门套，则应考虑两个问题：

If it is the former method - the stainless steel door pocket made on site is directly fixed on the door opening wall by the on-site decoration workers with nails; If a stainless steel door pocket of a complete set of door products is installed, two issues should be considered:

一是相应成套门产品的不锈钢门套的技术结构是否满足成套门产品所需的牢固、准确、稳定三大技术特征；

First, whether the technical structure of the stainless steel door pocket of the corresponding complete set of door products meets the three technical characteristics of firmness, accuracy and stability required by the complete set of door products;

二是整套门的安装人员应在安装现场进行事先调查，并规范安装过程中的工艺流程（如使用发泡剂可能会对不锈钢门的牢固性、准确性和未来使用稳定性产生所有可能的影响）。

Second, the installation personnel of the whole set of doors shall conduct a prior investigation at the installation site and standardize the process flow in the installation process (if foaming agent is used, it may have all possible effects on the firmness, accuracy and future use stability of stainless steel doors).

1.根据设计图纸检查门的规格、开启方向及相关附件。

1. Check the specification, opening direction and relevant accessories of the door according to the design drawings.

2.用卷尺测量车门开口的高度和宽度。门的标准高度和宽度为200cm×80cm；卫生间门高宽为200cm×70cm，如有尺寸偏差应及时纠正。

2. Measure the height and width of the door opening with a tape measure. The standard height and width of the door is 200cm × 80cm； The height and width of toilet door is 200cm × 70cm. Any dimensional deviation shall be corrected in time.

3.测量位置线，确定门框的位置，用喷墨器拉出垂直线，并在一侧拉出门洞的两条垂直线。

3. Measure the position line, determine the position of the door frame, pull out the vertical line with an inkjet, and pull out two vertical lines of the door opening on one side.

4.用冲击钻在垂直线上钻孔。两个孔之间的距离约为30厘米。一扇侧门的两排上有10个孔。冲击钻的钻头应为12mm，钻孔深约为6cm。

4. Use percussion drill to drill holes on the vertical line. The distance between the two holes is about 30 cm. There are 10 holes in the two rows of a side door. The bit of percussion drill shall be 12mm and the drilling depth shall be about 6cm.

5.将小木楔逐个锤入孔中，固定门框板。小木楔的体积为5cm×1.5cm×1.5cm，用落叶松制作更好，因为落叶松的木材结构紧密，不易松动。

5. Hammer the small wooden wedges into the holes one by one to fix the door frame plate. The volume of the small wooden wedge is 5cm × 1.5cm × 1.5cm, it is better to make it with Larch, because the wood structure of larch is compact and not easy to loosen.

6.切割材料制成门框。制作左右两侧门框龙骨的木工板尺寸为200cm×3cm×8cm，门框顶部龙骨的木工板尺寸为80cm×3cm×8cm，将高密度9cm板粘在龙骨上，用气枪钉固定。

6. Cut materials to make door frames. The dimension of the woodworking board for making the keel of the door frame on the left and right sides is 200cm × 3cm × 8cm, the dimension of the woodworking board of the keel on the top of the door frame is 80cm × 3cm × 8cm, stick the high-density 9cm board on the keel and fix it with air gun nail.

7.根据门的形状连接三个装配好的门框，并用大钉子将其固定在接缝处。

7. Connect three assembled door frames according to the shape of the door and fix them at the joint with large nails.

8.使用平面使连接的门框表面光滑，并用清晰的棱角修剪棱角。

8. Use a plane to make the surface of the connected door frame smooth, and trim the edges with clear edges and corners.

9将门框放在门洞上，以墙面水平线为准，在门框下垫木或砖，调整门框高度。预留5cm，埋入地板龙骨内。

9 place the door frame on the door opening, subject to the horizontal line of the wall, pad wood or brick under the door frame, and adjust the height of the door frame. Reserve 5cm and bury it in the floor keel.

10在门框上钉一颗钉子，垂直挂线，通过线垂调整门框的垂直度，用扭钉将门框测量固定在门洞上。

10 nail a nail on the door frame, hang the line vertically, adjust the verticality of the door frame through the line verticality, and measure and fix the door frame on the door opening with twist nails.

11在门的正面画线。门面可从货架上购买或由施工人员根据图纸制作。制作完成后，将门面固定在门框上，使不锈钢门套基本完成。

11 draw a line on the front of the door. The facade can be purchased from the shelf or made by the construction personnel according to the drawings. After fabrication, fix the door surface on the door frame to basically complete the stainless steel door pocket.

12将门放在不锈钢门套上，画出，确定铰链在不锈钢门套上的具体位置，然后根据铰链的厚度切割口径。同时切掉锁套的直径。将门安装在不锈钢门套上，并用铰链上的锣和钢丝刀拧紧锣和螺钉。注意门与不锈钢门套之间的间隙不大于1.5mm，以门的顺利开关为准。

12 place the door on the stainless steel door pocket, draw, determine the specific position of the hinge on the stainless steel door pocket, and then cut the caliber according to the thickness of the hinge. At the same time, cut off the diameter of the lock sleeve. Install the door on the stainless steel door pocket, and tighten the gong and screw with the gong and wire knife on the hinge. Note that the gap between the door and the stainless steel door pocket shall not be greater than 1.5mm, subject to the smooth opening and closing of the door.

以上就是为大家介绍的有关电梯门套线的详细介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sddtmt.com

The above is the detailed introduction of elevator door pocket line. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.sddtmt.com