基层处理：清理电梯门洞口周边的杂物、灰尘，确保基层平整、干燥。若洞口存在不平整或缺陷，需进行修复，如用水泥砂浆填补孔洞、用砂纸打磨突出部位，为后续安装提供良好基础。​

Grassroots treatment: Clean up debris and dust around the elevator door opening to ensure a smooth and dry base. If there are unevenness or defects in the opening, repair should be carried out, such as filling the hole with cement mortar or sanding the protruding part with sandpaper, to provide a good foundation for subsequent installation. ​

安装包口框架：将预先加工好的不锈钢包口框架，通过不锈钢螺丝或角码固定在电梯门洞口上。安装过程中要使用水平仪、铅垂线等工具，确保框架的水平度和垂直度，误差控制在 ±1mm 以内。框架安装牢固后，检查其与洞口的贴合度，如有缝隙，用密封胶填充密封。​

Installation of package frame: Fix the pre processed stainless steel package frame onto the elevator door opening with stainless steel screws or corner brackets. During the installation process, tools such as level gauges and plumb lines should be used to ensure the levelness and verticality of the frame, with an error controlled within ± 1mm. After the frame is firmly installed, check its fit with the opening. If there are gaps, fill and seal them with sealant. ​

安装面板：将经过表面处理的不锈钢面板安装在框架上，可采用粘贴、卡槽固定等方式。粘贴时，选用优质的结构胶，均匀涂抹在面板背面，确保粘贴牢固；卡槽固定则需提前在框架和面板上加工好对应的卡槽，安装时将面板准确嵌入卡槽内，轻轻敲打使其紧密结合。安装完成后，检查面板的平整度和拼接缝隙，缝隙宽度应均匀一致，一般不超过 0.5mm，若有缝隙过大或不平整的情况，及时调整。​

Installation panel: Install the surface treated stainless steel panel onto the frame using methods such as pasting or slot fixing. When pasting, use high-quality structural adhesive and evenly apply it to the back of the panel to ensure a firm adhesion; To fix the card slot, it is necessary to process the corresponding card slot on the frame and panel in advance. When installing, accurately insert the panel into the card slot and gently tap it to make it tightly fit. After installation, check the flatness and splicing gaps of the panel. The gap width should be uniform and consistent, generally not exceeding 0.5mm. If there are gaps that are too large or uneven, adjust them in a timely manner. ​

收口处理：对不锈钢包口的边缘、转角等部位进行收口处理，用密封胶填充缝隙，使边缘整齐、美观，同时增强防水、防尘性能。在电梯门与包口的交接处，安装橡胶密封条，减少关门时的碰撞噪音，提高密封性。

Sealing treatment: The edges, corners, and other parts of the stainless steel package are sealed with sealant to make the edges neat and beautiful, while enhancing waterproof and dustproof performance. Install rubber sealing strips at the junction of elevator doors and package openings to reduce collision noise during door closing and improve sealing performance.

本文由安徽不锈钢包口友情奉献.更多有关的知识请点击:http://www.sddtmt.com我们将会对您提出的疑问进行详细的解答，欢迎您登录网站留言.

This article is dedicated to friendship For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message