The stainless steel elevator door pocket has good metallic luster and reflective effect, the brushed stainless steel door pocket has Matt reflective effect, and the mirror stainless steel door pocket has mirror like reflective effect. This Gaoli door industry is incomparable with wood door jambs, which is also the reason why the hotel industry adopts stainless steel door jambs, which have metal elements. In many places, it is said that the door jambs are inclined to attract money.

石塑线条的出现，为绿色生活带来了很大的好处，而且石塑线条用在装修设计中，相比*的大理石不易划伤，而且还方便除尘，而且石塑线条的便面是经过石塑处理的，座椅大理石线条的表面*加的、防火、防水等，而且整体的视觉感官给人时尚华丽、大气的效果。

The appearance of stone plastic lines has brought great benefits to green life. Moreover, stone plastic lines are used in decoration design. Compared with * marble, they are not easy to be scratched, and they are also convenient for dust removal. Moreover, the convenient surface of stone plastic lines is treated with stone plastic. The surface of marble lines of seats is more environmentally friendly, fireproof and waterproof, and the overall visual sense gives a fashionable, gorgeous and atmospheric effect.

电梯门套的要求：

Requirements for elevator door pocket:

：作为公众场合进出人群密集之处，问题是重中之重。电梯门套一定要达到受破坏力撞击后破裂损坏无隐患，甚脱落不于危害或损坏生命财产（这类新闻日益增多）。

Safety: as a place where people go in and out of public places, safety is the top priority. The elevator door pocket must be broken and damaged after being hit by destructive force without potential safety hazard, or even fall off without endangering or damaging life and property (such news is increasing day by day).

使用寿命：作为公众设施，每天出入电梯人员/货物等众多，会对电梯门套造成很大的损伤和磨擦。对于电梯门套的材质需达到*高标准要求，以提高其使用寿命，电梯的使用寿命不少于16年，门套作为其组成部分，应尽量达到与电梯同寿命使用。

Service life: as a public facility, there are many people / goods entering and leaving the elevator every day, which will cause great damage and friction to the elevator door pocket. The material of the elevator door pocket shall meet the requirements of * high standard to improve its service life. The service life of the elevator shall not be less than 16 years. As a component of the elevator door pocket, it shall try to reach the same service life as the elevator.

常见的不锈钢电梯拉丝门套主要有竖边与横边90度拼角和横边与竖边45度拼角两种款式，*种款式线条很直，现场拼接非常方便，这也是常用的一款，后面的款式因为没有转折处，所以整个门套看起整体如一。

The common stainless steel elevator wire drawing door pocket mainly has two styles: the 90 degree angle between the vertical edge and the horizontal edge and the 45 degree angle between the horizontal edge and the vertical edge. The * style has straight lines and is very convenient for on-site splicing. This is also a commonly used one. The later style has no turning point, so the whole door pocket looks like one.

电梯门套的要求：

Requirements for elevator door pocket:

抗撞击强度：电梯轿厢门在《GB7588-2003》中规定要求在5cm*5cm的范围内，静力300N、撞击力1000N（约等于正常成年人所能施加的作用力，那么作为电梯门套应具备同等耐撞击程度，以防止提重物、或电动车、自行车等进出电梯时撞击发生损坏和意外。

Impact strength: the elevator car door is required to be within the range of 5cm * 5cm in GB7588-2003, with a static force of 300N and an impact force of 1000N (about equal to the force that can be applied by normal adults), so the elevator door sleeve shall have the same impact resistance to prevent damage and accident caused by impact when lifting heavy objects, electric vehicles, bicycles, etc. enter and exit the elevator.

防水阻燃：电梯为特种设备，在火灾情况下电梯是不允许使用的，但是电梯门套作为楼梯厅内重要部分，一定要达到相应阻燃要求（V0或以上），从而提高整体的消防等级；同理，若遭遇潮湿环境或被水泡情况，需达到浸水中泡**不开裂，以增强整体环境的性。

Waterproof and flame retardant: the elevator is a special equipment, which is not allowed to be used in case of fire. However, as an important part of the staircase, the elevator door pocket must meet the corresponding flame retardant requirements (V0 or above), so as to improve the overall fire protection level; Similarly, in case of wet environment or blistering, it is necessary to ensure that the bubble * * does not crack when immersed in water, so as to enhance the safety of the overall environment.

在安装电梯门套的侧板和线条时，要保证少有两个挂件作为支撑件，安装角钢的位置要丈量准确，在中间增加一个加固点的点位。

When installing the side plates and lines of the elevator door pocket, it is required to ensure that there are at least two hangers as the supports. The position of the installation angle steel shall be measured accurately, and a point of reinforcement point shall be added in the middle.

装配式电梯门套的安装是十分麻烦的，施工完成之后再重新拆卸是十分麻烦且费力的事情，只能采用填充的方法来进行。

The installation of the assembled elevator door pocket is very troublesome, and it is very troublesome and laborious to disassemble it again after the construction is completed. It can only be solved by filling.

以上就是为大家介绍的有电梯不锈钢门套的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sddtmt.com

The above is the detailed introduction of the stainless steel door cover of the elevator. I hope it will help you. If you have any questions, please contact us. We will provide you with services with a professional attitude http://www.sddtmt.com