不锈钢电梯门套常用的不锈钢板材分为201和304两种型号，实际上是成分不同，304质量好一些，但贵，201差一些，但作为家用也完全能满足需要。另外板材厚度也不同，一般商实际后的0.6的就足够了。板材表面处理也分为镜面和油膜拉丝两种，工装一般建议用镜面不锈钢，油膜拉丝的效果差一些。

　　The commonly used stainless steel plates for elevator door frames are divided into two types: 201 and 304. In fact, the composition is different. 304 has better quality, but it is more expensive. 201 is slightly inferior, but it can fully meet the needs of household use. In addition, the thickness of the board is also different. Generally, a practical 0.6 is sufficient. The surface treatment of sheet metal can also be divided into two types: mirror finish and oil film drawing. Generally, mirror finish stainless steel is recommended for tooling, but the effect of oil film drawing is relatively poor.

　　如何安装不锈钢电梯门套

　　How to install stainless steel elevator door frames

　　1、校对洞口

　　1. Proofread hole

　　洞口尺寸是否符合安装要求,不符合要求应予以必要的处理。

　　Whether the size of the opening meets the installation requirements, and if it does not meet the requirements, necessary treatment should be taken.

　　2、拆包检查

　　2. Unpacking inspection

　　检查门框、门套线、挡门条、密封条，零部件是否齐。

　　Check if the door frame, door frame line, door stop strip, sealing strip, and components are complete.

　　3、组装门框

　　3. Assembling door frames

　　门框组装时竖框与横框搭接处必须涂胶，然后用自攻丝予以固定。

　　When assembling the door frame, the overlap between the vertical and horizontal frames must be coated with glue, and then fixed with self tapping screws.

　　4、定位门框

　　4. Positioning the door frame

　　门框按室内标高线就位，先用木楔从门框周围夹紧门框，再用工装和木楔从门框内口撑紧门框，通过夹门框内外木楔，调整门框竖直度、水平度及门框内径尺寸，使其达到设计要求。

　　The door frame is positioned according to the indoor elevation line. First, use wooden wedges to clamp the door frame around it, and then use fixtures and wooden wedges to support the door frame from the inner opening. By clamping the wooden wedges inside and outside the door frame, adjust the verticality, levelness, and inner diameter of the door frame to meet the design requirements.

　　5、门框注胶

　　5. Door frame gluing

　　门框与墙体间填充发泡胶前要清理干净墙体，用喷壶湿润墙面，填充发泡胶，注意发泡胶填充要适量，多余发泡胶用刀片切平。

　　Before filling the gap between the door frame and the wall with foam adhesive, the wall should be cleaned thoroughly, moistened with a spray can, and filled with foam adhesive. Pay attention to filling the foam adhesive in an appropriate amount, and use a blade to cut off excess foam adhesive.

　　6、做好门套

　　6. Make good door frames

　　将不锈钢按照设计要求裁剪出来，做成一个门套，

　　Cut the stainless steel according to the design requirements and make it into a door frame,

　　6、安装门套线

　　6. Install door frame wire

　　待4-6小时发泡胶固化后，卸下工装和木楔，在门框嵌槽内涂胶，然后将门套线嵌入门框，轻轻敲紧压实使门套线与墙体紧密贴合。

　　After 4-6 hours of curing of the foam adhesive, remove the tooling and wooden wedge, apply adhesive to the embedded groove of the door frame, and then embed the door frame line into the door frame. Gently tap and compact to make the door frame line tightly adhere to the wall.

　　7、安装门扇

　　7. Install door leaf

　　注意门的开启方向，安装五金，门扇与门框间隙达到设计要求，保证门扇开关灵活。

　　Pay attention to the opening direction of the door, install hardware, and ensure that the gap between the door leaf and the door frame meets the design requirements, ensuring that the door leaf switches flexibly.

　　本文由 潍坊电梯门套 友情奉献.更多有关的知识请点击    http://www.sddtmt.com  真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is dedicated to the friendship of Weifang elevator door frames. For more related knowledge, please click http://www.sddtmt.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned