不锈钢门套线包边的做法 1.用冲击电钻在门四周大洞眼,并插入木楔。

Method for wrapping stainless steel door frame wire: 1. Use an impact drill to create large holes around the door and insert wooden wedges.

2.将15厘 大芯板 (或夹板)靠墙侧进行防潮处理(刷 光油 2遍后在贴珍珠棉)。用钉枪校正固定后,再用铁钉加固。

2. Apply moisture-proof treatment to the 15cm large core board (or plywood) against the wall side (brush with gloss oil twice and then apply pearl cotton). After correcting and fixing with a nail gun, reinforce with iron nails.

门套线条打底用9厘夹板。打底夹板外侧用实木线条收口。合页位置加板衬固或封两层15厘大芯板。

Use 9cm plywood as the base for the door frame lines. The outer side of the base plywood is closed with solid wood lines. Add board lining or seal two layers of 15cm large core board at the hinge position.

3.门套与门扇相合之处到进门边的侧面用9厘夹板做止口板,止口深度与门的厚度相同。

3. Use 9cm plywood to make a stop plate from the point where the door frame and door leaf match to the side of the entrance, with the depth of the stop plate being the same as the thickness of the door.

4.面板用 白乳胶 涂匀后贴于打第大芯板及止口板上,并用不锈钢蚊钉适当加固。

4. Apply white latex evenly to the panel and stick it onto the largest core board and stopper board, and reinforce it appropriately with stainless steel mosquito nails.

5.门套线条宽度一般为60mm—80mm.厚度8mm.

5. The width of the door frame line is generally 60mm to 80mm, and the thickness is 8mm

6.厨卫门套线条里侧用不锈钢(哑光)线条为宜。

6. It is advisable to use stainless steel (matte) lines on the inner side of the kitchen and bathroom door frames.

7.门套及 门窗 套垂直、水平误差不超过2mm(2m以上不超过3mm)对角线误差不超过3mm(2m以上不超过5mm).

7. The vertical and horizontal errors of door frames and door and window frames shall not exceed 2mm (not exceeding 3mm for 2m and above), and the diagonal error shall not exceed 3mm (not exceeding 5mm for 2m and above)

8.门套两侧墙与门套之间距离在门套线条不能压住接缝时,宜先用 水泥砂浆 挂钢钉封平(用板定模灌浆)干燥后方可封板打第,在门套线条能压住接缝时可用板封龙骨结构。

8. When the distance between the walls on both sides of the door frame and the door frame cannot be pressed against the joint by the door frame line, it is advisable to first use cement mortar to hang steel nails and seal it flat (with board fixed mold grouting) before sealing the board. When the door frame line can press against the joint, the board can be used to seal the keel structure.

9.单面门套用9厘板打底(凸窗应注意 窗帘 位置)。其他与双面门套同。

9. Single sided door frames should be lined with 9cm boards (attention should be paid to the position of the curtains for protruding windows). Same as double-sided door frames.

入户大门可封单边实木线条门套。

The entrance door can be sealed with a single-sided solid wood door frame.

10.窗套不宜包台面,台面用 大理石 铺贴(防盗网宜在窗套面板封后制作)。

10. Window frames should not cover countertops, which should be paved with marble (anti-theft nets should be made after the window frame panel is sealed).

单面门套:在原来有门的基础上起装饰作用,不起承受门的力量。 做不锈钢门套线包边的注意事项 不锈钢门套线包边一般都是定制加工,很少有现场制作的,因为目前工人的技术水平达不检验评定标准,而且现场也没有的不锈钢施工操作人员。

Single sided door frame: It serves as a decoration on the basis of the original door and does not bear the force of the door. Precautions for stainless steel door frame wire edging: Stainless steel door frame wire edging is generally customized and rarely made on site because the current technical level of workers does not meet the inspection and evaluation standards, and there are no professional stainless steel construction operators on site.

本文来自：菏泽拉丝不锈钢电梯门套线更多的内容请点击：http://www.sddtmt.com 我们将会为您提问的问题提供一个满意的服务，欢迎您的来电！

This article is from: Heze brushed stainless steel elevator door frame wire. For more content, please click: http://www.sddtmt.com We will provide satisfactory service for the questions you ask. Welcome to call us!