Stainless steel glass doors are common to everyone. They are mainly used in some large shopping malls, and the installation method also requires some skills. Do you know the installation method? Today, Luban home furniture installer introduced the installation process and precautions of stainless steel glass doors to you. Interested friends can learn about it.

一，不锈钢玻璃门的安装方法

1、 Installation method of stainless steel glass door

1.定位线。在不锈钢玻璃门安装开始时，固定玻璃间距和可移动玻璃门扇需要定位在一个统一的位置，并确定固定门框的方向，以及地面的高度和高度应测量门框顶部的位置。

1. Positioning line. At the beginning of the installation of stainless steel glass door, the fixed glass spacing and movable glass door leaf need to be positioned in a unified position, and the direction of the fixed door frame and the height and height of the ground should be determined. The position of the top of the door frame should be measured.

2.在门框顶部安装限位槽。从子弹的线绘制两个金属装饰板边缘，然后通过侧线安装门框的顶部位置。

2. Install a limit slot on the top of the door frame. Draw two metal trim panel edges from the center line of the bullet, and then install the top position of the door frame through the side line.

3.金属饰面的木质底部用原始预埋木砖上的膨胀螺栓或方木钉在木块上，然后将金属饰面粘在木质面上。

3. The wooden bottom of the metal facing is nailed to the wood block with expansion bolts or square wood on the original embedded wood bricks, and then the metal facing is glued to the wooden surface.

4.设备牢固地固定在门框上。根据子弹的线，门框被钉牢，然后胶合板用于确定门框的方向和形状。固定后，然后包裹金属装饰表面。

4. The equipment is firmly fixed on the door frame. According to the center line of the bullet, the door frame is nailed, and then plywood is used to determine the direction and shape of the door frame. After fixing, wrap the metal decorative surface.

5.玻璃门扇装置。不锈钢玻璃门通过玻璃吸盘用厚玻璃吸入，然后使用吸盘将厚玻璃板抬起23人并将其竖立到设备位置。

5. Glass door leaf device. The stainless steel glass door is sucked with thick glass through the glass suction cup, and then the thick glass plate is lifted by the suction cup for 2 to 3 people and erected to the equipment position.

6.玻璃是固定的。两个扁平方条在内托盘的内侧和外侧钉牢，厚玻璃夹在中间，但距离厚玻璃板约4毫米，然后在平木条上涂上贴面金属板。它被粘在两块扁平木条和方木上。

6. The glass is fixed. Two flat square strips are nailed firmly on the inner and outer sides of the inner tray, and the thick glass is clamped in the middle, but about 4mm away from the thick glass plate, and then the veneer metal plate is coated on the flat wood strip. It is glued to two flat wooden strips and square timber.

7.注塑玻璃密封。在顶部根槽两侧的开放空间和底部玻璃槽的两侧，以及厚玻璃和门框柱的相对侧，注入玻璃胶。

7. Injection glass seal. Inject glass glue into the open space on both sides of the top root groove, both sides of the bottom glass groove, and the opposite side of the thick glass and the door frame column.

8.在玻璃之间对接。具有固定部分的厚玻璃板需要由两个或更多个部件组装，因为宽度太大。两个拼接件需要形成一个接头，接头间距应为23毫米。

8. Butt joint between glasses. Thick glass plates with fixed parts need to be assembled by two or more parts because the width is too large. Two splices need to form a joint, and the joint spacing should be 2 to 3 mm.

二，不锈钢玻璃门安装注意事项

2、 Precautions for installation of stainless steel glass door

1.安装前，需要确保施工结束后内部装修过程完成，并且定位的位置应严格按照规划图纸进行。

1. Before installation, it is necessary to ensure that the internal decoration process is completed after the construction is completed, and the positioning position should be carried out in strict accordance with the planning drawings.

2.玻璃门框顶部的限位槽的槽深在20到30mm之间，并且宽度优选地比玻璃的厚度大24mm用于注射。

2. The groove depth of the limit groove on the top of the glass door frame is between 20 and 30mm, and the width is preferably 2 to 4mm larger than the thickness of the glass for injection.

3.当外包金属装饰表面时，应将遮盖的接缝放置在装置玻璃两侧的。接缝方向需要准确和笔直。

3. When the metal decorative surface is wrapped, the covered joint shall be placed in the center of both sides of the device glass. The joint direction needs to be accurate and straight.

4.放置玻璃门扇时，玻璃杯的上部应插入门框顶部的限位槽中，然后玻璃的下部应放在线上，并且方向为两侧的门框应该是厚玻璃的两侧刚好覆盖门框面向接缝的金属框架，并且要求在桌子上看不到接缝。

4. When placing the glass door leaf, the upper part of the glass should be inserted into the limit slot on the top of the door frame, and then the lower part of the glass should be placed on the center line, and the door frame on both sides should be thick glass, and both sides of the door frame should just cover the metal frame facing the joint, and the joint should not be seen on the table.

5.密封玻璃胶时，注射顺序应从一定间隙结束开始到结束，不应中途停止。

5. When sealing the glass glue, the injection sequence should start from the end of a certain gap to the end, and should not stop halfway.

6.在玻璃对接接头的过程中，需要使用接头的玻璃切割，固定玻璃后，应将玻璃粘在间隙中。填充后，塑料片应用塑料片压平，使间隙构成清洁。均匀的直线，用干净的布擦拭玻璃表面。

6. In the process of glass butt joint, the glass of the joint needs to be cut. After fixing the glass, the glass should be stuck in the gap. After filling, the plastic sheet shall be flattened to make the gap clean. Wipe the glass surface with a clean cloth in a uniform straight line.

以上就是为大家介绍的有关不锈钢玻璃门的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sddtmt.com

The above is a detailed introduction about stainless steel glass doors. I hope it will help you If you have any questions, please contact us We will provide you with professional service http://www.sddtmt.com